Style group white
Stylegroup woodsense2
March 17, 2026
1 Minute Read time

The Warmth of Wood. The Freedom of HPL

Chelsea
http://style-partitions.co.uk

With the new Wood Sense HPL Collection, Dorma Huppe brings the character of real wood to a surface that is reliable and easy to specify in the project process. The wood laminate décors are visually and tactually very close to natural wood, while remaining consistent and dependable when it comes to selection, ordering and replacement.

A key feature is the continuous large pattern repeat. Many décors are available in heights of up to 4,100mm, allowing expansive surfaces without visual interruptions. This creates significantly more design freedom – especially when wood is intended to create sense of warmth and wellbeing across an entire wall, rather than in smaller sections.

The collection includes 16 wood options, presented as large-format samples, and enables efficient specification through quick sampling. All laminates are supplied with an EPD label, supporting sustainability requirements in modern project planning.

Discover the Wood Sense HPL Collection. Click here to learn more

2026 © Style Group

Subscribe to our newsletter

Zero-Joint Technology in the Healthcare Sector

NHS England’s Health Building Note 00-09 states clinical surfaces should be “impervious, designed for easy cleaning and free of fissures and unsealed joints.”
  • Laser-bonded, adhesive-free edge, with no seam or adhesive strip
  • Designed in line with the surface characteristics HBN 00-09 describes for clinical areas
  • Formaldehyde emissions tested significantly below the EU's REACH formaldehyde limit, in effect from 6 August 2026

Why it matters

HBN 00-09 sets out these surface characteristics because unsealed joints are a recognised place for moisture and micro-organisms to collect. A genuinely joint-free edge is designed to address that specific detail.

This is a surface and edge specification, not a clinical claim. Zero-joint technology has not been evaluated or certified by NHS England, and does not claim to reduce infection rates.

Zero-Joint Technology in the Hospitality Sector

Guest-facing spaces and food-service areas face frequent hygiene inspections and heavy daily use — seamless panels help simplify housekeeping and keep finishes looking newer for longer.
  • Seamless edge finish, with no visible transition between edge and panel surface
  • 100% adhesive-free construction — no hot-melt adhesive layer to fail
  • Edge processing on all four sides, built for daily commercial use
  • Low-maintenance and easy to clean

Why it matters

Food-service and guest-facing areas are typically inspected under hygiene and housekeeping standards that look closely at surfaces and joints. A seamless, moisture-resistant edge is designed with exactly that kind of scrutiny in mind.

Every one of these sectors shares the same underlying surface problem: a bonded-strip edge is a seam, and a seam is a place where dirt, moisture or wear can concentrate in a way a continuous surface can't. Zero-joint technology addresses that one structural detail across offices, schools, healthcare and hospitality settings alike — one construction detail, one shared weak point removed, four sectors that each care about it for their own reasons.

Zero-Joint Technology in the Education Sector

Classrooms and shared facilities see high daily footfall from children and staff, so partitioning needs to withstand daily wear and support fast, thorough cleaning.
  • Seamless, adhesive-free edge with no strip to lift or wear loose over time
  • Moisture-resistant, low-maintenance surface
  • Independently tested for VOC emissions to AgBB and EN 16516

Why it matters

Schools see some of the highest footfall of any building type relative to their size, and surface durability directly affects how long fittings stay presentable between refurbishment cycles. A seam-free edge that can't lift or peel with repeated impact and cleaning is a genuinely lower-maintenance fixture over the life of the building.

Zero-Joint Technology in the Corporate Sector

Open-plan offices and meeting suites see constant daily use — surfaces need to look sharp for years without high maintenance.
  • Seamless edge finish, with no visible transition between edge and panel surface
  • 100% adhesive-free construction — no hot-melt adhesive layer to fail
  • Edge processing on all four sides, built for daily commercial use
  • Low-maintenance and easy to clean

Why it matters

An adhesive seam is one of the few places on a standard partition edge where dust, spillage residue or cleaning-product build-up can collect, simply because it isn't a flat, continuous surface. Removing that seam removes that particular weak point — a lower-maintenance fixture designed to stay looking sharp for longer.

Prefer to Write?

Fill in the form below and we’ll get back to you within one working day.

Apply Now

Fill in the form below and we’ll get back to you within one working day.

    Book a CPD with us

    Fill in the form below and we'll get back to you as quickly as we can.

    Download pdf icon

    Download

    Would you like to be contacted?